Ashly ne800 Stereo Power Amplifier, 2 x 400W at 4 Ohms

Product Description

Ashly's two-channel NE amplifiers for the performance installation and constant voltage markets, the ne800, ne1600 and the ne2400 add a new level of power and control from the simplest to most advanced audio system applications. The ne800 provides 400W, ne1600 800W and ne2400 1200W per channel at four ohms. Input connections are XLR-1/4" Neutrik combo connectors and 6-pin Euroblock. XLR male and Euroblock connectors are also provided for looping to additional amplifiers. Output connectors are locking Neutrik Speakon (NL-4) and Euroblock.

Network Enabled (NE) amplifiers offer ease of use, full setup, control and monitoring using standard 10/100 Ethernet protocol and Protea NE Software. No special outboard control units are needed. NE Series amplifiers are offered two ways; standard and "pe" (Protea Enabled) with our world renowned Protea DSP signal processing.

The DSP library is extensive and utilizes two SHARC 32-bit/96kHz processors. Processing blocks include Graphic, Parametric, Notch and Shelving Equalization, High-, Low- and All-Pass Filters (HPF/LPF/APF) with up to 48dB/Octave slopes, Delay, Compressor/Limiter, Gate, Ducking, Auto-leveler, Gain and Signal Generators (sinewave, white and pink noise). A full Matrix Mixer with assignable routing allows any input to drive any or all amplifier outputs. Presets can be used to store and retrieve global parameters of an entire amplifier's control surface and DSP section.

Additionally, each amplifier also provides DC voltage control of the attenuators which makes it a snap to control volume from remote locations, preset recall, Remote Power Standby and data in and out ports for connecting accessories like the WR-5 to control user selected parameters. There are LED indicators for power, standby, protect, network communications and each channel has a four-step signal meter, bridge mono, temperature and current indicators. AES/EBU and Cobranet input modules options are also available.

Features

• Ethernet control is standard
• Low-Z, 25V, 70V and 100V Models
• Extensive DSP Option Available
• Easy and intuitive user interface
• Extensive protection circuitry
• Safety/Compliance: FCC, CE, RoHS
• Level attenuators for each channel
• Power switch can be disabled by software
• 4-Step Signal Level and Clip LEDs
• 10/100 Ethernet port
• Euroblock inputs and outputs
• Remote level control
• Remote power standby
• Optional Cobranet and AES/EBU input modules

Specifications

• 8 ohms power rating: 225W per channel
• 4 ohms power rating: 400W per channel
• 8 ohms mono bridge power rating: 800W per channel
• Frequency Response (8 ohms) 20 Hz - 20k Hz, ±1.0dB
• Distortion (SMPTE, typical) <0.5% (8 ohm load, 10dB below rated power)
• Distortion (THD+N, typical) <0.5% (8 ohm load, 10dB below rated power)
• Input Impedance 20k ohms, balanced
• Input Sensitivity 26dB, 32dB or 1.4V
• Maximum Input Level +21dBu
• Damping Factor >250 (8 ohm load, <1KHz)
• Front Controls AC Power Switch, Individual input attenuators
• Cooling Temperature dependent speed controlled fan, Front-in, Rear-out flow
• Control Network onboard, standard 10/100 Ethernet
• Connectors (each channel) Input: XLR Female, Euroblock, Looping: XLR male, Euroblock
  Output: Speakon, Euroblock
• Connections (Remote) Standby, Level: Euroblock
• Front indicators per channel: Clip, -6dB, -12dB, -18dB, Temp, Current, Bridge, Power, Standby, Protect, Power Switch Disable, Comm
• Amplifier and Load Protection inrush current limitation, temperature monitoring, output over-current protection, mains fuses
• Dimensions Height: 3.50" (88.9mm) 2RU Width: 19" (483 mm) Depth: 15.5" (394mm)
• Weight: Net 21 lbs (9.53kg), Shipping 27.0 lbs (12.25kg)
• Environmental 40-120deg. F, (4-49deg. C) noncondensing

For more information on this product, please visit the Ashly website.

Can't find what you're looking for?
We sell this manufacturer's entire product line!
Call 1(800)433-2105 or email sales@proaudio.com for a quick quote.